Call: 888-333-4642  

Revision [697]

This is an old revision of W123AntennaMast2 made by WebMaster on 2009-08-20 17:21:09.

 

Antenna mast replacement (with old cable stuck inside the motor housing)

on the 1983 300CD (W123)

by Yak

8/19/09



Repair: Antenna mast replacement when the plastic/nylon stub has disappeared inside the motor
housing and won’t come out. The photos and references are specific to the Hirschmann AUTA 6000U,
or, I assume, the factory power antenna on an ’83 300CD. This one has a smooth cable.

Situation: you know or suspect that there is some part of the old cable stuck inside the motor housing. I
knew the cable was in there since mine went inside while troubleshooting and wouldn’t come back out.

Other symptoms: (speculative) you replaced the old mast and the new mast won’t retract all the way.

How I got here: I bought an ’83 300CD that had a cell phone antenna jammed into the antenna slot (no
kidding!). The previous owner provided me with two old Hirschmann motors, but neither was installed
and it wasn’t clear if either worked or how they would connect to the factory wiring. Time for some
research and troubleshooting to 1) see if either motor worked and 2) if they were reparable. During the
initial test to see if the motor worked, it retracted the remaining nylon stub into the motor housing. I
could hear the motor whir and a slight click.

Results: after removing the stub and installing a new mast, everything worked correctly on my test runs.
If it fails in the near future, I’ll amend the DIY. What I have now based on radio + antenna switch
settings:

Links:
Peachparts antenna mast threads:
- W123 Power Antenna Mast Replacement
- W123 Power Antenna Gear Replacement

Hirschmann technical page, w/ exploded diagrams:
Hirschmann electric aerials

Tools/materials (if antenna motor was already removed from car):

image

1) With the motor out of the car remove the four Philips screws from the cover.

2) Inspect the motor and see if you can see the nylon cable stub. On my car it had retracted away from the friction gear and the pressure wheel. I replicated what it looked like with the red spray nozzle (see pic). If the stub has retracted away from the gears, there is no friction to move the nylon cable. SPECULATION ALERT: I think if your motor was in this condition and you tried to replace the mast, it is possible that you could shove the old stub into the take-up reel and then feed the new cable into the take-up reel which may prevent the new antenna from completely retracting. The basis for my speculation is that I removed two feet of nylon cable from the take up reel after disassembly. I’m not sure if there is two feet of “extra” space in there. A clue to whether you completely removed the whole cable MAY be whether your old cable had a tapered end (see pic). I assume the removed cable was an original and compared it to my replacement mast. The one I removed, which I assume was factory original, had a taper at the very end.

image
Pic showing where the cable stopped retracting/extending. Arrow shows it out from the pressure wheel and the friction gear (my terms, maybe not technically correct).
image
If it were correctly routed, you’d see the white nylon cord following the path of the red spray tube. The motor could then extract the cord and you wouldn’t need to do this repair.

image
Arrow shows tapered end of old – probably original – cable. Maybe a useful check to see if you got the full cable out before putting the new one in. The upper cable is the squared end of the brand-new replacement cable. This is a sample size of one, so no guarantees that this means anything.

3) Remove the three screws holding the motor mechanism within the case (see pic).
image
Pic taken with three screws already removed. Screws are in approx 11, 2, and 7 o’clock positions.

4) Carefully turn the motor mechanism over and remove the circlip that holds the takeup reel in place (see pic). I used a 90-degree angle pick to slide it off.
image
Take-up reel with circlip removed.

5) BE PREPARED FOR THE TAKE-UP REEL TO POP-OFF. Once the circlip is removed, the plastic take-up reel may “unwind” from slight compression of the nylon cord, sort of like an electric weedwhacker. It’s not a problem nor is it dangerous. I assume the shaft and the gearing on the other side of the mechanism will not fall out, but that’s an assumption based on my one-time disassembly. I would recommend being careful as you flip this thing around.

6) Pull the remaining nylon cord out of the motor mechanism.

7) With the take-up reel removed and the motor mechanism out of the case, I did some housecleaning. There was a lot of dirt-caked grease right at the entry way to the take up reel. I scraped out what I could and blew the rest out with compressed air. I also cleaned off the pressure wheel next to the friction wheel. I thought it was a black rubber gear until the black goo flaked off. It’s actually a clean metal bearing (see above in the pic with the red spray tube – notice it’s a shiny wheel). I also used the angle pick to carve some pressed-in gunk out of the friction gear.
image
Pic showing goo scraped from friction gear.

8) I re-lubed the shaft upon which the take-up reel rotates and reassembled everything. Needle nose pliers slid the circlip back into place (see pic).
image

9) A quick spritz of contact cleaner onto the electrical connections and then replace the cover and the four screws.
image

10) Reinstall the antenna motor into your car, then install the mast using conventional instructions available HERE.

Total time: less than an hour

Additional info:

Pinouts were not in accordance with references, if you’re really interested I can scan hires and send pics from the maintenance manual (page 82.3-530/2) or from the dedicated MB electrical manual for the 300 series (page 133). The scans were crappy unless I go really hi-res.

Mercedes connector in car

Wires on antenna (no connector, just loose pins, I think I’m missing some sort of pig-tail adapter)

More info:

The factory default auto setting for the antenna is 30 cm extension (or about 15 inches). To move it past this position you need to have the antenna switch in the dash working. I didn’t check, but I assume this is “X” number of rotations from the parked position. I’ve seen comments in other posts about the antenna “not fully extending” and the Mercedes/Hirschmann’s behavior of 30 cm extension is definitely different than the standard “fully in or out” of other non-tunable antennas. I took photos of the motor (sans antenna) in parked/off, auto, and max extension (see pics).

image
Above: Gears in “Off” after motor did it’s retraction thing. There is no cable installed, so there was no “friction/pressure” stop. Gears form a “9 o’clock”

image
Above: Gears in “Auto” after motor did it’s auto extension thing. Gears form a two-thirtyish. Friction gear circumference multiplied by X-and-a-half rotations equals 30 cm? Max extension left the gears in the same position as “Auto” and Off always returned them to the 9 o’clock position.


Discuss this DIY here.

-Yak

CategoryDiy
Valid XHTML :: Valid CSS: :: Powered by WikkaWiki



PeachParts, LLC all rights reserved 1999 -
PeachParts, LLC takes no responsibility whatsoever for any technical assistance offered by anyone. The Risk is 100% yours.